MULTI-MONTI-plus zinc-plated steel screw anchor, MMS-plus-V pre-positioning anchor with metric connecting thread
MULTI-MONTI-plus MMSplus-V pre-positioning anchor, galv. steel, SW7 10x130/55/70
Drill, screw in, done
Register now and access more than 125,000 products
Drill, screw in, done
The concrete screw anchor is an innovative anchoring system for securing assembly parts to concrete and other solid masonry. With its cutting-teeth design, the concrete screw anchor cuts a thread in the drill hole as it is screwed in, creating a connection with mechanical interlocking and no expansion pressure.
Application area:
For securing
staircase railings, grilles, beams, brackets, metal structures, formwork supports, cable conduits, pipes, mounting rails, ventilation ducts, suspended ceilings, sprinkler systems etc.
to
normal weight concrete with a strength class of at least C20/25 and up to maximum C50/60, solid sand-lime brick, hollow sand-lime brick, masonry brick and lightweight concrete.
Field of Application:
Also suitable for hard-to-reach areas and slotted holes (e.g. mounting rails) due to its smaller drive and pressed-on washer
Advantages:
- Approved for use in masonry (note types and dimensions)
- Shallow drill hole depths and small drill hole diameters
- Cutting teeth at the fore of the anchor ensure minimal tightening torque
- No expansion effect, hence minimal spacing and edge distance
- Quick and simple in-place installation, can be easily inserted by mechanical means
- Immediate load-bearing capacity - no waiting
- Fastening can be fully removed again
- No torque control required
- Broad range of uses due to numerous versions
- Attractive design with countersunk hexagon head
Advice:
Thanks to the testing sleeves 0901 000 010/012/016/020, the concrete screw anchors in diameters 10-20 can be used multiple times for temporary fastenings. (Note the types and dimensions)
Datasheets(X)
 | |
Type description | MMS-plus V pre-positioning anchor with metric connecting thread |
Anchor diameter x anchor length (l) | 10 x 130 mm |
Nominal drill-bit diameter (d 0) | 8 mm |
Connection thread | M10 x 60 |
Drill hole depth (h 1) | 75 mm |
Drill hole depth reduced (h 1, red) | 60 mm |
Max. attachment height (t fix) | 70 mm |
Max. attachment height reduced (t fix, red) | 55 mm |
Surface | Zinc plated |
Material | Steel |
External drive | WS7 |
Approval | Yes |
Embedding depth (h nom1) | 50 mm |
Embedding depth (h nom2) | 65 mm |
Effective anchoring depth (h ef) | 50 mm |
Effective anchoring depth reduced (h ef, red) | 36 mm |
Centre-to-centre distance in concrete (s) | 50 mm |
Min. centre-to-centre distance (s min) | 40 mm |
Edge clearance in concrete (c) | 50 mm |
Min. edge clearance (c min) | 40 mm |
Minimum component thickness for concrete (h min) | 115 mm |
Reduced minimum component thickness (h min) | 100 mm |
Permissible bending torque (M perm) | 20.4 Nm |
Through-hole in the component to be connected (d f) | 12 mm |
Max. recommended power output for setting tool | 250 Nm |
Installation torque for connection thread | 20 Nm |
Last viewed
Carbide-tipped construction site circular saw blade
PRESSURE WASHER PORTABLE LITE 1510 XP
Wall brackets from the ZS 41 toothed mounting rail system
HARDCON tile drill bit, round shaft
sebS zinc-plated hexagon head self-drilling screw similar to DIN 7504-K
HSS-Co twist drill bit DIN 338
HEADGEAR FOR PROTECTIVE VISOR
TIE ROD WING
Lashing strap, width 35 mm, 1000/2000 daN
x-tron SDS-Plus hammer drill bit incl. trade pack